Geotech Monitoring
Meatech Solutions
Geotech Monitoring
MX2301A
HOBO Temperature/RH Data Logger A weatherproof data logger with built-in temperature and relative humidity sensors, leveraging Bluetooth for easy setup and data download.
A weatherproof data logger with built-in temperature and relative humidity sensors. Leveraging Bluetooth technology for easy setup and data download directly to your mobile device or Windows computer running Onset’s free HOBO connect app, this logger delivers high-accuracy measurements even in harsh outdoor environments.
HOBO RX3000 Remote Weather Station Starter Kit
Cellular Weather Station
This kit provides instant access to site-specific air temperature, relative humidity, and wind speed & direction data anywhere, at any time, from your desktop or mobile device.
Hydro Sense II Handheld Soil Moisture Sensor with Insertion Pole
The HS2P is a combination of the Hydrosense II soil-water sensor with a strong handle and pole that make it easier to insert the probes into the soil. The lightweight pole allows soil testing without bending over. The HS2P is compact and portable, with the layout of the buttons on the display allowing for operation with one hand. Two different probe lengths are available, for different types of soil or turf.
The compact agrometeo station that counts every drop
Quido is much more than just a rain gauge. It is the environmental monitoring system that alerts you also on any specific weather conditions.
In this way you may know when it’s raining, even miles away from you, and plan the working day in the best way, via smartphone or PC.
Quido collects a large amount of certified information (in addition to rain, it measures temperature, humidity and leaf wetness and soil condition). You can look into and evaluate the data at any time, planning activities to increase the competitiveness of your farm. Or you can use the certified data for insurance or forecasting purposes in the treatments.
It does not require any specific configuration; it is ready to use. It can be installed in a few minutes and the data is already in your hands, at a very low cost.
Leaf wetness sensor
The leaf wetness sensor can determine the degree of leaf wetness, the duration of a certain state (wet or dry) and detects whether there are precipitations or condensation. Depending on the degree of humidity, the sensor detects a change in electrical resistance on the elements of the grid and the output signal can be acquired by a data logger (standard output 0÷2 Vdc, or normalized 4÷20 mA or digital RS485/Modbus).
VIBRATING WIRE STRAIN GAUGE
The vibrating wire strain gauges are used to measure stress in load-bearing structures or monitor tensions in tunnel linings during tunnel excavation phases.
SURFACE TILTMETER
Surface clinometers are essential tools for monitoring the inclination of structures, retaining walls, rock masses, and analyzing the behavior of bridges or beams under load.
BOREHOLE ROD EXTENSOMETERS
Extensometers are used to monitor the displacement between one or more points located along the shaft of a borehole and the reference head installed at its end.
These instruments are used for monitoring subsidence, foundation settlements, convergence during excavation, landslides, wall and diaphragm deformations, piling, and for controlling deep movements in soil or rock masses.
ELECTRICAL CRACKMETER
The Electric Crackmeter uses a potentiometric displacement transducer to detect changes in position between two points located near a joint or injury.
WIRE DISPLACEMENT SENSOR
Wire displacement sensors detect ground movement in unstable areas, offering reliable geotechnical monitoring in high-risk environments.
DISPLACEMENT TRANSDUCERS
The displacement transducers are commonly used to run on automatically and continuously the measurements of borehole rod extensometers. It is necessary to install one displacement transducer for each point of measure in order to transform the mechanical movement of the rod into an electrical signal.
IN-PLACE INCLINOMETER
In-place Inclinometers are instruments connected through a stainless steel cable, forming a column. They are used to continuously monitor soil movements, landslides, and structural control of dams, walls, bulkheads, poles, masts, etc.
Datalogger - NI2400
The displacement transducers are commonly used to run on automatically and continuously the measurements of borehole rod extensometers. It is necessary to install one displacement transducer for each point of measure in order to transform the mechanical movement of the rod into an electrical signal.
Datalogger - NI103
NI103 is a highly efficient modbus data logger designed for structural health monitoring applications. This versatile device is capable of reading various types of digital sensors, and can be expanded to include analog devices through external modules.
